|
 |
Our Suction Cups and Straps mounting kit can be used for temporary or semi-permanent mounting. These are not difficult to install and make your signrack look professional and secure.
Kits shown with 4 suction cups are for
the RT-III and RT-IV Model Kit comes with Ratchet Straps that extend thru your vehicle door jams or vent windows or Stainless-Steel Hooks that grab the rain gutter or door frame. Brackets alone can also be used in combination with
some roofracks or our channel kit. Click any image for larger view. |
 |
 |
|
 |
|
 |
|
| |
|
| |
|
| |
|
RT-I |
$69 With 4 Cups and Ratchet Straps |
RT-II |
$75 With 6 Cups and Ratchet Straps |
RT-III |
$82 With 8 Cups and Ratchet Straps |
RT-24 RCK
24" Roof Channels |
$49 With Hardware
Black Powdercoated Steel |
|
|
|
|
Rivet Studs for roof
mounting |
|
 |
Blind rivet nuts and
blind rivet studs are specially manufactured for fastening thin walled
materials and can be quickly and easily fitted to thin sheet components.
Thin sheet fastening usually requires welding nuts or studs to thin
sheet, or drilling and threading. It is a common problem that
deformation of material or breaking of welding spots occurs by welding
nuts or studs. Direct drilling hole and threading will cause loose
fastening. The use of blind rivet nuts and blind rivet studs can avoid
such problems. Blind rivet nuts and blind rivet studs need only a
prefabricate punched or drilled hole for installation, no welding or
threading is required. It can also be installed to components where
access is available from one side only |
|
Bulb-tite Rivets for
roof mounting |
|
  |
- HOW THE BULB-TITE WORKS:
- During installation the
rivet body folds into three separate legs, forming
the blind-side upset head. The Bulb-tite mandrel
breaks off *flush with the rivet head. *Flush
mandrel break requires use of special Bulb-tite
installation tool nose tip.
- WEATHER TIGHT:
- A special nose tip on the
rivet installation tool crimps a crown feature on
the rivet head. This crown-crimp effectively seals
the rivet bore off from intrusion of dirt and
moisture. Adding the optional washer to the Bulb-tite,
creates an additional seal around the perimeter of
the rivet head, to stop moisture from intruding
beneath the rivet head.
- HIGH STRENGTH:
- Another benefit of the
Bulb-tite rivetís retained mandrel core is the added
strength it provides. Bulb-tite rivets are less
prone to failure in high shear loads.
- HIGH CLAMPING:
- The large three-legged
upset head evenly distributes the Bulb-tite rivetís
high clamp load over a broader bearing surface than
do conventional blind rivets. This enables soft,
thin, ductile and even brittle materials to be
securely clamped without deformation, cracking or
other damage to the application.
- HARD-TO-FASTEN
APPLICATIONS:
- Bulb-tite rivets function
well in materials where other fasteners fail. The
folded legs individually conform to curved surfaces
enabling fastening onto pipes, corrugations and
other challenging shaped applications. Oversized or
elongated holes can be adequately covered by the
large leg formations to resist pull through under
stress in high tension-load applications.
- MULTI-GRIP
- CAPABILITY: Each Bulb-tite
handles a wide variation in material thickness. Most
sizes fasten over a 1/4" thickness range. Fewer
rivet sizes may be required resulting in reduced
inventory requirements and simplified fastener
selection.
|
|
Plusnuts for
roof mounting |
 |
Plusnut
blind fasteners for the most rigid fastening. A Plusnut® is a
blind, threaded fastener recommended for rigid fastening in
sheet metal, fiberglass and plastics. The slotted shank spreads
and forms large flaps to evenly distribute working loads over a
large area. Plusnut fasteners are ideal when you cannot access
one side, or if it is very difficult to do so. The plusnut is
easy to use, and yet maintains the strength and integrity needed
for industrial or heavy duty applications. |
|
 |
- Provides ultimate
pull-out strength in thin or soft materials.
- Wide grip range.
- Easy installation
with hand or automatized tooling.
|
|
|
 |
4 Gang fuse protected switchbox
recommended for multi-circuit lightbars.
(1) 30 amp and (3) 15 amp switches.
$52
|
|
| |
|
PRICE $550.00
